Home About Us Contact Us Products List Woodwork Built Cars Balustrades Wardrobe shoemaker miniature

Home About Us Contact Us Products List Woodwork Built Cars Balustrades Wardrobe shoemaker miniature Lacquered Wooden Seats in decape Crafts Furniture Kitchen furniture and flooring infant Doors Furniture Restoration Furniture Upholstery antigüos sale Altars Torneados Articles of Interest Links Our interest in Avila Blog A handyman jobs: restoring butts jobs: tables for boar tusks jobs: transport and packing of furniture
Now we will explain you have to do when you get the furniture, they will seem a mountain of packages bread bin with which you can install. The furnishings are hung and placed at the height of the sides of the refrigerator.
The sides of the fridge bread bin are usually 2.30 m. or 2.10 m. depending on the height of tall furniture or hang. High or hanging bread bin usually 90 or 70 cm tall furniture, there are other standard measures but these two are usually the most common. If your kitchen has no refrigerator sides (because this is only one place you can change the height bread bin at which they hang, but it is recommended that you do at this point because it is possible that the wall units are made inaccessible bread bin if you hang too up or that much joined at the counter if lower).
Shape is hanging or placing remaining subtracting the height bread bin from the roof of the cabinet to the hanger, depending on the type of these hangers may vary but the operation is equally subtracting the distance from the ceiling of the cabinet to the hanger.
It is very practical to draw a continuous line with the level marking with pencil underneath, drawing the line on which the holes will be. This line should be below the top of the cabinet (it is the height of the holes in the wall hangers).
We mark the holes in the wall hangers then drill them all. When holes are marked and put the plugs and screwed to the wall (usually come with the furniture, these studs and screws)
The cabinet can be somewhat uneven or desaplomado but later when they are all hung and assembled the nivelaremos and regulating aplomaremos hangers with screws you bring to this effect.
The furnishings are assembled to each other by screws 3.5 x 30 mm. Are normal bolts screwed a piece of furniture to another at the height of the shelves and hinges. So once put these will not be opening the kitchen cupboard. Once assembled place them in each level will move furniture and screw the hangers to aplomen leveled and all the furniture, then will press the center screw snug against bread bin the wall and do not move. This operation will repeat on all the furniture. If you purchased the furniture already assembled (by volume) as in the picture above. If you've purchased disassembled to mount the kilt to fit you like the photo, bread bin but the doors to make it easier to mount first.
Currently there are decorative legs of steel, aluminum and different bread bin ways they do not take socket. The height of the legs must be one that allows the entry of the socket underneath bread bin the furniture.
The base units are joined to each other in the same way that high but there is furniture that anchor them to the wall with a hole in BHI (low oven and plate) and under sink. These two do not carry furniture back and even this is limited to upper batten about 10 cm. wide in this batten taladraremos for tightening the screw is the batten to the wall.
Furniture should be flush prior to assembly each other so that when the legs nivelemos by behaving like a block. When placed both high and low furniture we will consider the previous design, making sure all are in place and if possible in line high to low: and the draining should be above the sink and decorative hood or lock in place on top of the plate or the kitchen:
To perform this task it is advisable to have a miter saw or miter because unless it is completely bread bin straight this should bring a miter where furniture out more than others and in the refrigerator, furniture boiler or light bearer of the hood cabinet.
The way to cut this ledge and light bearer (the light bearer cornice itself is usually placed underneath the wall units) is the side that is going to be in contact with the disc or the sawtoothed. This means that the tab should bread bin be done in this manner in order to prevent chipping assault bread bin and leaving the disk.
The cornice is screwed from the roof of the furniture with the same type of screws to assemble the furniture. In miter apply white glue or adhesive d